Shurjoint HEAVY DUTY RIGID COUPLING-Angle-Pad Design

Z07

C-06

MODEL Z07 HEAVY DUTY RIGID COUPLING

-Angle-Pad Design-

The Shurjoint Model Z07 is an angle-pad design rigid coupling for general piping applications where rigidity is required including valve connections, mechanical rooms, fire mains and long straight runs. The angle-pad design allows the coupling housings to slide along the bolt pads when tightened. The result is an offset clamping action which provides a rigid joint that resists flexural and torsional loads. Support and hanging requirements correspond to ANSI B31.1, B31.9 and NFPA 13.

The Shurjoint Model Z07 is available with a standard “C” shaped or GapSeal® gasket in a variety grades to meet your specific service requirements.

Z07 couplings should always be installed so that the coupling bolt pads make metal to metal contact.

For Fire Protection pressure rating, listing, and approval information, refer to Data Sheet B-42 or visit SHURJOINT website, www.shurjoint.com for details or contact your SHURJOINT Representative.

1¼"~24”	14” ~ 18”	20” ~ 24”	Full	warranty terms
			can	be found on
Z07 & Z07N			www.shurjoint.com

Model Z07 Standard Rigid Coupling

			Max.	ASME/ANSI	Max.
			Working	Pressure Class	End		Axial		Dimension			Bolt
	Nominal	Pipe	Pressure	Rating^	Load		Displace-
	Size	OD	(CWP)*	@100oF/@38oC	(CWP)		ment †	A	B	C	No		Size	Weight
	in	in	PSI	PSI	Lbs		in	in	in	in			in	Lbs
	mm	mm	Bar	Nom. Class	kN		mm	mm	mm	mm			mm	Kgs
1¼		1.660	750	750	1620		0 ~ 0.05	2.68	4.13	1.85	2		⅜ x 2⅛	1.6
32		42.2	52	300	7.27	0~1.2		68	105	47			M10 x 55	0.7

1½		1.900	750	750	2120	0 ~ 0.05		2.91	4.53	1.85	2		⅜ x 2⅛	2.0
40		48.3	52	300	9.52	0~1.2		74	115	47			M10 x 55	0.9

2		2.375	750	750	3320	0 ~ 0.07		3.39	4.72	1.88	2		⅜ x 2¾	2.4
50		60.3	52	300	14.84	0~1.7		86	120	48			M10 x 70	1.1

2½		2.875	750	750	4860	0 ~ 0.07		3.94	5.50	1.88	2		⅜ x 2¾	2.4
65		73.0	52	300	21.75	0~1.7		100	140	48			M10 x 70	1.1

	76.1 mm	3.000	750	750	5290	0 ~ 0.07		4.00	5.75	1.88	2		⅜ x 2¾	2.4
		76.1	52	300	23.64	0~1.7		102	146	48			M10 x 70	1.1

3		3.500	750	750	7210	0 ~ 0.07		4.53	6.18	1.88	2		½ x 3	3.1
80		88.9	52	300	32.26	0~1.7		115	157	48			M12 x 75	1.4

4		4.500	750	750	11920	0 ~ 0.16		5.78	7.83	2.13	2		½ x 3	4.4
100		114.3	52	300	53.33	0~4.1		147	199	54			M12 x 75	2.0

	139.7 mm	5.500	750	750	17810	0 ~ 0.16		6.88	9.25	2.13	2		⅝ x 3½	6.6
		139.7	52	300	79.66	0~4.1		175	235	54			M16 x 90	3.0

5		5.563	750	750	18220	0 ~ 0.16		6.97	9.25	2.13	2		⅝ x 3½	6.6
125		141.3	52	300	81.50	0~4.1		177	235	54			M16 x 90	3.0

	165.1 mm	6.500	700	750	23210	0 ~ 0.16		7.87	10.20	2.13	2		⅝ x 3½	7.5
		165.1	48	300	102.71	0~4.1		200	259	54			M16 x 90	3.4

6		6.625	700	750	24110	0 ~ 0.16		8.00	10.35	2.13	2		⅝ x 3½	7.1
150		168.3	48	300	106.73	0~4.1		203	263	54			M16 x 90	3.2

8		8.625	600	400	35030	0 ~ 0.19		10.55	13.46	2.52	2		¾ x 4¾	15.7
200		219.1	42	250	158.27	0~4.8		268	342	64			M20 x 120	7.1

10		10.750	500	400	45350	0 ~ 0.13		12.86	16.98	2.56	2		⅞ x 6½	27.4
250		273.0	35	250	204.77	0~3.2		327	431	65		---		10.4

C-06-1/4 Rev.G		20130220

					Z07								C-06

			Model Z07 Standard Rigid Coupling
		Max.	ASME/ANSI	Max.
		Working	Pressure Class	End	Axial		Dimension					Bolt
Nominal	Pipe	Pressure	Rating^	Load	Displace-
Size	OD	(CWP)*	@100oF/@38oC	(CWP)	ment †	A	B	C		No			Size	Weight
in	in	PSI	PSI	Lbs	in	in	in	in					in	Lbs
mm	mm	Bar	Nom. Class	kN	mm	mm	mm	mm					mm	Kgs
12	12.750	400	400	51040	0 ~ 0.13	14.86	18.88	2.56	2				⅞ x 6½	26.0
300	323.9	28	250	230.59	0~3.2	377	480	65			---			11.8

200 JIS	8.516	600	400	34150	0 ~ 0.13	10.39	13.39	2.50	2				¾ x 4¾	16.3
	216.3	42	250	154.25	0~3.2	264	340	64					M20 x 120	7.4

250 JIS	10.528	500	400	43500	0 ~ 0.13	12.63	15.63	2.56	2				⅞ x 6½	23.1
	267.4	35	250	196.45	0~3.2	321	397	65			---			10.5

300 JIS	12.539	400	400	49360	0 ~ 0.13	14.65	17.80	2.56	2				⅞ x 6½	27.4
	318.5	28	250	222.97	0~3.2	372	452	65			---			12.4

14	14.000	250	300	38460	0 ~ 0.13	16.06	19.89	2.95	3				⅞ x 5½	32.7
350	355.6	17	150	168.75	0~3.2	408	505	75			---			14.8

16	16.000	250	300	50240	0 ~ 0.13	18.39	21.84	2.95	3				⅞ x 5½	37.5
400	406.4	17	150	220.41	0~3.2	467	554	75			---			17.0

18	18.000	250	300	63580	0 ~ 0.13	20.68	23.89	3.11	3				⅞ x 5½	47.0
450	457.2	17	150	278.95	0~3.2	525	607	79			---			21.3

20	20.000	250	300	78500	0 ~ 0.13	22.93	27.47	3.11	4				1 x 5½	52.0
500	508.0	17	150	344.39	0~3.2	582	698	79			---			23.6

24	24.000	250	300	113040	0 ~ 0.13	27.05	31.61	3.15	4				1 x 6½	64.6
600	609.6	17	150	495.92	0~3.2	687	803	80				---		29.3

14 (Z07N)	14.000	250	300	38460	0 ~ 0.13	16.06	19.89	2.95	2				⅞ x 5½	35.3
350	355.6	17	150	168.75	0~3.2	408	505	75			---			16.0

16 (Z07N)	16.000	250	300	50240	0 ~ 0.13	18.39	21.84	2.95	2				⅞ x 5½	30.5
400	406.4	17	150	220.41	0~3.2	467	554	75			---			17.9

18 (Z07N)	18.000	250	300	63580	0 ~ 0.13	20.68	23.89	3.11	2				⅞ x 5½	40.1
450	457.2	17	150	278.95	0~3.2	525	607	79			---			22.3

20 (Z07N)	20.000	250	300	78500	0 ~ 0.13	22.93	27.47	3.00	2				1 x 5½	57.8
500	508.0	17	150	344.39	0~3.2	582	698	76			---			26.2

24 (Z07N)	24.000	250	300	113040	0 ~ 0.13	27.05	31.61	3.06	2				1 x 5½	70.8
600	609.6	17	150	495.92	0~3.2	687	803	78			---			32.1

Note: Model Z07N two-segment couplings are now available in sizes 14” - 24”.						Please specify the model required when ordering.

* Working Pressure is based on roll grooved standard wall carbon steel pipe.

^ The ASME/ANSI pressure class rating is not the design or maximum pressure rating, rather is provided for those that are accustomed to specifying or using ASME/ANSI pressure class rated components such as flange, valves, etc.

† Allowable Axial Displacement and Angular Movement (deflection) figures are for roll grooved standard steel pipe. Values for cut grooved pipe will be double that of roll grooved. These values are maximums; for design and installation purposes these figures should be reduced by: 50% for 3/4” – 3 1/2”; 25% for 4” and larger to compensate for jobsite conditions.

MATERIAL SPECIFICATIONS

Housing:

Ductile Iron to ASTM A536, Gr. 65-45-12 and or ASTM A395 Gr.65-45-15, min. tensile strength 65,000 psi (448 MPa).

Surface Finish:

Standard painted finishes in orange or RAL3000 red.

Hot dip zinc galvanized (Optional).

Epoxy Coatings in RAL3000 red or other colors (Optional)

Rubber Gasket:

Grade “E” EPDM (Color code: Green stripe) Good for cold & hot water up to +230oF (+110oC). Also good for services for water with acid, water with chlorine, deionized water, seawater and waste water, dilute acids, oil-free air and many chemicals.

Not recommended for petroleum oils, minerals oils, solvents and aromatic hydrocarbons.

Maximum Temperature Range: -30oF (-34oC) to +230oF (+110oC) *.

*EPDM gaskets for water services are not recommended for steam services unless couplings or components are accessible for frequent gasket replacement.

(Option) Grade “T” Nitrile (Color code: Orange stripe) Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. Also good for water services under +150oF (+66oC).

Temperature range: -20 oF to +180 oF (-29 oC to +82 oC).

Do not use for HOT WATER above +150 oF (+66 oC) or HOT DRY AIR above +140 oF (+60 oC).

Other options: Grade “O” - Fluoroelastomer.

Grade “L” - Silicone.

For dry systems we recommend the use of the Shurjoint GapSeal® gasket.

For additional details contact Shurjoint.

Bolts & Nuts:

Heat treated carbon manganese steel track bolts to ASTM A449-83a (or A183 Gr. 2), minimum tensile strength 110,000 psi (758 MPa), Zinc electroplated, with heavy-duty hexagonal nuts to ASTM A563.

C-06-2/4 Rev.G 20130220

Z07

C-06

Performance Data

The following tables show the maximum working pressures (CWP) of Shurjoint Model Z07 Standard Rigid Coupling used on both carbon steel and stainless steel pipes. Shurjoint ductile iron couplings can be used in conjunction with stainless steel pipe in non-corrosive environment as the flow media does not come in direct contact with the coupling housings but rather only the gasket.

Unit: psi / Bar

Model Z07 on Carbon Steel Pipe

Nom. Size	Cut-Grooved		Roll-Grooved
in / mm	XS	STD	STD	Sch. 10	Sch. 7
1¼	750	750	750	600	400
32	52	52	52	42	28
1½	750	750	750	600	400
40	52	52	52	42	28
2	750	750	750	600	400
50	52	52	52	42	28
2½	750	750	750	600	400
65	52	52	52	42	28
2½	750	750	750	600	400
65	52	52	52	42	28
3	750	750	750	600	400
80	52	52	52	42	28
4	750	750	750	600	400
100	52	52	52	42	28
5	750	750	750	500	350
125	52	52	52	35	24
5	750	750	750	500	350
125	52	52	52	35	24
6	700	700	700	400	300
150	48	48	48	28	20
6	700	700	700	400	300
150	48	48	48	28	20
8	600	600	600	350	250
200	42	42	42	24	17
10	500	500	500	300	200
250	35	35	35	20	14
12	400	400	400	250	150
300	28	28	28	17	10

Unit: psi / Bar

Model Z07 on Stainless Steel Pipe

	Nom. Size	Cut-Grooved		Roll-Grooved
	in / mm	Sch. 80S	Sch. 40S	Sch. 40S	Sch. 10S	Sch. 5S
1¼		750	750	700	500	300
32		52	52	48	35	20
1½		750	750	700	500	300
40		52	52	48	35	20
2		750	750	700	500	300
50		52	52	48	35	20
2½		750	750	700	500	300
65		52	52	48	35	20
2½		750	750	700	500	300
	65	52	52	48	35	20
	3	750	750	700	500	300
80		52	52	48	35	20
4		750	750	700	400	250
100		52	52	48	28	17
5		750	750	600	300	NR
125		52	52	42	20	NR
125		52	52	42	20
5		750	750	600	300	NR
	125	52	52	42	20	NR
	125	52	52	42	20
	6	700	700	500	200	NR
150		48	48	35	14	NR
150		48	48	35	14
6		700	700	500	200	NR
150		48	48	35	14	NR
150		48	48	35	14
8		600	600	400	150	NR
	200	42	42	28	10	NR
	200	42	42	28	10
	10	500	500	300	100	NR
250		35	35	20	7	NR
250		35	35	20	7
12		400	400	250	100	NR
300		28	28	17	7	NR
300		28	28	17	7

C-06-3/4 Rev.G 20130220

Z07

C-06

LISTINGS/APPROVALS

The information provided below is based on the latest listing and approval data at the time of publication. Listings/Approvals are subject to change and/or additions by the approvals agencies. Contact Shurjoint for the performance on other pipes and the latest listings and approvals

Standard Pipe
	Nom. Size	cULus	cULus/FM		VdS	LPCB
	in	Sch. 5	Sch. 10	Sch. 40
	mm

		PSI / Bar	PSI / Bar	PSI / Bar	Bar	PSI / Bar
	1¼	175	500	500	16	300
	32	12	35	35	16	20
	32	12	35	35		20
	1½	175	500	500	16	300
	40	12	35	35	16	20
	40	12	35	35		20
	2	175	500	500	16	300
	50	12	35	35	16	20
	50	12	35	35		20
	2½	N/A	500	500	N/A	N/A
	65	N/A	35	35	N/A	N/A
	65		35	35
	76.1mm	N/A	500	N/A	16	300
	76.1mm	N/A	35	N/A	16	20
			35			20
	3	N/A	500	500	16	300
	80	N/A	35	35	16	20
	80		35	35		20
	4	N/A	500	500	16	300
	100	N/A	35	35	16	20
	100		35	35		20
	139.7mm	N/A	400	N/A	16	300
	139.7mm	N/A	28	N/A	16	20
			28			20
	5	N/A	400	400	N/A	N/A
	125	N/A	28	28	N/A	N/A
	125		28	28
	165.1mm	N/A	400	N/A	N/A	300
	165.1mm	N/A	28	N/A	N/A	20
			28			20
	6	N/A	400	400	16	N/A
	150	N/A	28	28	16	N/A
	150		28	28
	8	N/A	400	400	16	300
	200	N/A	28	28	16	20
	200		28	28		20
	10	N/A	350	350	12.5	300
	250	N/A	24	24	12.5	20
	250		24	24		20
	12	N/A	350	350	12.5	300
	300	N/A	24	24	12.5	20
	300		24	24		20
* Model Z-07 incorporating Lube-E gasket is cULus listed and also suitable for use in dry pipe systems for temperatures to -40°F (-40°C).

General Notes:

ASME/ANSI Pressure-Temperature Rating is provided as an aid in selecting a proper coupling to incorporate with other piping components (valves, flanges, and etc.) that are used in the same system and carry the ASME/ANSI rating. Select a Class 150 coupling to incorporate with Class 150 valves and flanges.

Maximum Working Pressure (CWP) listed is the maximum cold water pressure for general piping services tested to ASTM F1476 and or AWWA C606 methods. Figures listed are based on roll- or cut-grooved standard wall carbon steel pipe. For other pipe schedules or pipe materials, contact Shurjoint for additional information.

Max. End Load is calculated based on the maximum working pressure (CWP).

Listed and or Approved Pressures are pressure ratings for fire protection systems, tested and approved by various approval bodies. Please always refer to the latest approval data posted on the Shurjoint website.

Field Joint Test: For one time only the system may be tested hydrostatically at 1 1/2 times the maximum working pressure listed (AWWA C606 5.2.3).

Warning: Piping systems must always be depressurized and drained before attempting disassembly and or removal of any components.

The 10 Year Limited Warranty applies to manufacturing defects only and does not cover severe service/temperature applications or wear parts.

Shurjoint reserves the right to change specifications, designs and or standard without notice and without incurring any obligations.

Job Name:	System No.		Location:
Contractor:		Approved:	Date:
Engineer:		Approved:	Date:

Shurjoint product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Shurjoint Technical Service. Shurjoint reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligations to make such changes and modifications on Shurjoint products previously subsequently sold.

C-06-4/4 Rev.G 20130220

C&C Hose And Fittings
Toronto Ontario Canada
(416) 439-2315

Site Map

Copyright © 2010 C&C Hose and Fittings – All Rights Reserved.

C&C Hose And Fittings Toronto Ontario Canada (416) 439-2315

Site Map

Copyright © 2010 C&C Hose and Fittings – All Rights Reserved.

C&C Hose And Fittings
Toronto Ontario Canada
(416) 439-2315