R20 |
MODEL R20
-
The Shurjoint Model R20
The fluid will neither directly contact the rubber gasket nor stay in the gasket pocket as often seen in conventional grooved pipe couplings. No rubber ingredients will leach out into the fluid.
The T&G (tongue & groove) device supported by the Shurjoint precise casting technique provides a
No special changes are required when processing
Applications:
All piping including mechanical rooms where no angular and axial movement are desired.
Stainless steel piping for potable water and food industries (epoxy coated housings with NSF61 certified gasket and type 316 bolts and silicone bronze nuts).
Hot water systems.
Caution: Pipe end shall be cut square so that pipe ends come to butt together.
For Fire Protection pressure rating, listing, and approval information, refer to Data Sheet
Full warranty terms can be found on www.shurjoint.com
Model R20
|
|
|
Max. Working |
ASME/ANSI Pressure |
Max. End |
|
Dimension |
|
|
|
|
|
|
|||
|
Nominal |
|
Pressure |
Class Rating^ |
Load |
|
|
|
|
|
|
|
||||
|
Size |
Pipe O.D. |
(CWP)* |
@100oF/@38oC |
(CWP) |
A |
|
B |
C |
|
Bolt Size |
Weight |
||||
|
in |
in |
PSI |
PSI |
|
Lbs |
|
in |
|
in |
in |
|
|
in |
Lbs |
|
|
mm |
mm |
Bar |
Nom. Class |
kN |
|
mm |
|
mm |
mm |
|
|
mm |
Kgs |
|
|
2 |
2.375 |
300 |
300 |
|
1330 |
|
3.39 |
|
4.92 |
1.81 |
|
|
⅜ x 2⅛ |
1.9 |
|
|
50 |
60.3 |
20 |
150 |
|
5.71 |
|
86.0 |
125.0 |
46.0 |
|
|
M10 x 55 |
0.9 |
|
||
|
76.1 mm |
3.000 |
300 |
300 |
|
2120 |
|
4.00 |
5.55 |
1.81 |
|
|
⅜ x 2⅛ |
2.1 |
|
|
|
76.1 |
20 |
150 |
|
9.09 |
|
102.0 |
141.0 |
46.0 |
|
|
M10 x 55 |
1.0 |
|
||
|
|
|
|
|
|
|
||||||||||
3 |
3.500 |
300 |
300 |
|
2880 |
|
4.53 |
6.18 |
1.81 |
|
|
⅜ x 2¾ |
2.9 |
|
||
80 |
88.9 |
20 |
150 |
|
12.41 |
|
115.0 |
157.0 |
46.0 |
|
|
M10 x 70 |
1.3 |
|
||
4 |
4.500 |
300 |
300 |
|
4770 |
|
5.75 |
7.52 |
2.00 |
|
|
⅜ x 2¾ |
3.9 |
|
||
100 |
114.3 |
20 |
150 |
|
20.51 |
|
146.0 |
191.0 |
51.0 |
|
|
M10 x 70 |
1.8 |
|
||
|
139.7 mm |
5.500 |
300 |
300 |
|
7120 |
|
6.69 |
9.21 |
2.00 |
|
|
½ x 3 |
5.4 |
|
|
|
139.7 |
20 |
150 |
|
30.64 |
|
170.0 |
234.0 |
51.0 |
|
|
M12 x 75 |
2.4 |
|
||
|
|
|
|
|
|
|
||||||||||
|
165.1 mm |
6.500 |
300 |
300 |
|
9950 |
|
7.80 |
9.92 |
2.00 |
|
|
½ x 3 |
6.3 |
|
|
|
165.1 |
20 |
150 |
|
42.80 |
|
198.0 |
252.0 |
51.0 |
|
|
M12 x 75 |
2.9 |
|
||
|
|
|
|
|
|
|
||||||||||
|
200 JIS |
8.516 |
300 |
300 |
|
10340 |
|
10.11 |
13.00 |
2.50 |
|
|
⅝ x 3½ |
12.5 |
|
|
|
216.3 |
20 |
150 |
|
44.47 |
|
256.8 |
330.4 |
63.4 |
|
|
M16 x 90 |
5.7 |
|
||
|
|
|
|
|
|
|
||||||||||
* Working Pressure is based on roll or cut- grooved standard wall carbon steel pipe. |
|
|
|
|
|
|
|
|
|
^ The ASME/ANSI pressure class rating is not the design or maximum pressure rating, rather is provided for those that are accustomed to specifying or using ASME/ANSI pressure class rated components such as flange, valves, etc.
R20 |
MODEL R20 MATERIAL SPECIFICATIONS
• Housing:
Ductile Iron to ASTM A536, Gr.
(Option) Gr.
• Surface Finish:
Standard painted finishes in orange or RAL3000 red.
Hot dip zinc galvanized (Option).
Epoxy Coatings in RAL3000 red or other colors (Option)
•Rubber Gasket:
GapSeal gasket, Grade “E” EPDM (Color code: Green stripe) Recommended for cold and hot water service within the specified temperature range, plus a variety of dilute acids, alkalis, salts,
oils and gases.
Do not use for HYDROCARBONS and PETROLEUM service.
Temperature range:
*EPDM gaskets for water services are not recommended for steam services unless couplings or components are accessible for frequent gasket replacement.
General Notes:
(Option) Grade “T” Nitrile (Color code: Orange stripe) Recommended for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. Also good for water services under +150oF (+66oC).
Temperature range:
Do not use for HOT WATER above +150 oF (+66 oC) or HOT DRY AIR above +140 oF (+60 oC).
Other options: Grade “O” - Fluoroelastomer.
Grade “L” - Silicone.
For additional details contact Shurjoint.
• Bolts & Nuts:
Heat treated carbon manganese steel track bolts to ASTM
Stainless steel type 316 track bolts with silicone bronze nuts
ASME/ANSI
Maximum Working Pressure (CWP) listed is the maximum cold water pressure for general piping services tested to ASTM F1476 and or AWWA C606 methods. Figures listed are based on roll- or
Max. End Load is calculated based on the maximum working pressure (CWP).
Listed and or Approved Pressures are pressure ratings for fire protection systems, tested and approved by various approval bodies. Please always refer to the latest approval data posted on the Shurjoint website.
Field Joint Test: For one time only the system may be tested hydrostatically at 1½ times the maximum working pressure listed (AWWA C606 5.2.3).
Warning: Piping systems must always be depressurized and drained before attempting disassembly and or removal of any components.
The 10 Year Limited Warranty applies to manufacturing defects only and does not cover severe service/temperature applications or wear parts.
Shurjoint reserves the right to change specifications, designs and or standard without notice and without incurring any obligations.
Job Name: |
System No. |
|
Location: |
Contractor: |
|
Approved: |
Date: |
Engineer: |
|
Approved: |
Date: |
Shurjoint product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Shurjoint Technical Service. Shurjoint reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligations to make such changes and modifications on Shurjoint products previously subsequently sold.
FRASERS Industrial Supply Companies
www.canadianbusinessdirectory.ca